Exactly How to Remove and Change a Bathtub

Quote & Schedule

The article below about Installing A Bathtub is definitely attention-grabbing. Don't miss it.

Mounting a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bathtub with a new one is also a reasonably hard task. If the old bathtub is conveniently obtainable, the job can move quickly; if you have to open a wall to get rid of the old bathtub and also place the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub as well as set in the new one. Make certain you have actually qualified yourself for the work and also fit attempting it. Rather than hiring a service provider to take control of a halfway-completed project, it is better to take into consideration using one prior to you begin. Chances are you might require a professional plumber to make tube connections.
This write-up will certainly assist you install a brand-new tub in your bathroom if you have actually already acquired a brand-new tub and do not need to transform the arrangement of your previous water pipes.
Your devices and material checklist must comprise the following:

New Tub

Hammer

Pipe Wrenches

Prybar

Shatterproof glass

Level

Pliers

Flexible Wrench

Putty Knife

Screwdriver

Cold Blade

Tape Measure

Pipeline Caps

Preparing for the Setup

To start with, the supporting structure supplied with the bath needs to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make sure that if the faucet features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to prevent stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last placement.

Removing Old Taps

If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the staying water that will come from the pipelines. When the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before proceeding to fit the brand-new faucets, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.

Setting up the Bath tub

Utilizing the two wooden boards under its feet, place the bathtub in the called for position. The wood boards are handy in evenly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the tub until the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Turn on the supply of water and check all joints and also new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as likewise examine the overflow outlet and the typical electrical outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the maker's instruction manual. Tiling and securing around the tub should wait till the tub has been utilized at least once as this will certainly settle it right into its final placement.

Suitable New Taps

If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making sure that the washing machines are in location between the tap and also the sink. Secure the faucet in place with the producer supplied backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

Tiling Around the Bathtub

In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a rigid seal, triggering the water to permeate the wall surface between the bath and the tiling, resulting in issues with wetness and feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your fixtures and installations. They are marketed in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can split rather very early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly readily available on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water resistant sticky and also cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

We hope you enjoyed our excerpt about How to Install a Bathtub. Many thanks for spending some time to read through our blog. Enjoyed our post? Please share it. Help other people locate it. Thank you for your time. Kindly stop by our website back soon.

Book Maintenance